BUILT IN GEORGETOWN, TEXAS 🇺🇸

THE CONTAINER POOL COMPANY

Ref: CPC-INST-TX-DAL

Location

Dallas, TX // Dallas County

Crew base

Fort Worth, TX // ≈ 32 mi

Path

/locations/texas/dallas

Installation // Dallas, TX

Shipping container pools in Dallas, TX

A pool built in a Texas shop, water-tested, and set in your Dallas backyard by crane. Our crew is based in Dallas–Fort Worth, so Dallas installs carry no travel charges. A basic 8x20 with a simple install on a flat Dallas lot typically comes to $50,000–$100,000 all-in.

DALLAS–FORT WORTH / CREW BASEI-30 ≈ 32 MIDALLASFORT WORTHPLANOFRISCOMCKINNEY
Service area

Who a container pool fits in Dallas

Dallas yards come in two flavors that traditional pools struggle with:

  • Tight infill and alley-loaded lots in places like the M Streets, Lakewood, Oak Lawn and East Dallas. Rear yards are narrow, the garage often eats half of them, and a dig crew has no room to work. An 8x20 fits a side yard or along a back fence. An 8x40 gives you a real 40-foot lap lane in an 8-foot strip.
  • Large, established lots in Preston Hollow, Highland Park and University Park, where people want a modern, architectural pool, a raised pool with a deck, or a long lap lane next to a pool house. That's where the 16-wide models come in.

With us you get the founder on your design call, along with the fabrication and installation partners who'll build and set your pool, plus real numbers in writing.

What a container pool costs in Dallas

Typical
Base-configuration pool (pool only)Custom-quoted by size
Basic install on a flat Dallas lot (site prep, level slab, crane, electrical, plumbing)~$25,000
Simple 8x20 project, all-in$50,000–$100,000
Sloped lots, raised pools on piers, elevated decks, in-ground$100,000+

Freight from Georgetown, about 190 miles down I-35, is quoted to your address. An 8-wide pool travels on a standard flatbed, and a 16-wide pool is an oversize load. Dallas installs don't carry the crew travel and lodging line that installs outside North Texas do. Full breakdown: how much a container pool costs in Texas.

Permits in Dallas: yes, you need one

People ask whether an above-ground pool skips the permit. In Dallas, a prefabricated pool is exempt only if its wall is entirely above the adjacent grade, it holds 5,000 gallons or less, and it's under 24 inches deep. A container pool is well over 24 inches deep, so it's permitted like any other residential pool.

The City of Dallas pool permit checklist asks for a scaled, dimensioned site plan showing:

  • North arrow, all property lines, easements and platted building lines
  • The footprint of every structure, with front, side and rear setbacks
  • The pool footprint, plus the location of the filter, pump, heater and other equipment
  • The fence, wall or barrier enclosing the pool
  • Either an alarm on doors and gates into the pool area or self-closing, self-latching doors and gates
  • Pool specifications

Electrical and plumbing work need their own separate permits, and a pool on top of a building needs engineered drawings. Dallas won't accept incomplete or illegible submittals, which is one reason we draw the site plan from your survey rather than a sketch.

Setbacks for a pool in a Dallas backyard

Dallas zoning has specific relief for small accessory structures. In residential districts, a residential accessory structure 15 feet tall or less in the rear 30% of the lot doesn't need a side-yard setback (Sec. 51A-4.402(b)(3)). In the rear yard, it needs 3 feet if the yard backs onto an alley, and no rear setback otherwise (Sec. 51A-4.403(b)(2)). Planned developments, conservation districts and deed restrictions can override this, so we confirm your exact lot before the design is final.

Conservation and historic districts

Dallas has dozens of conservation and historic districts. Conservation districts such as the M Streets (Greenland Hills), Hollywood/Santa Monica, Kessler Park and Greenway Parks use a staff-level work review against the district's ordinance. Historic districts such as Swiss Avenue, Munger Place, Junius Heights and Winnetka Heights generally need a Certificate of Appropriateness, often through the Landmark Commission. Most district rules focus on what's visible from the street, including fences, landscaping and driveways, which matters for a pool barrier. If you're in one, we add the review to the schedule up front.

Highland Park and University Park are separate towns

They're surrounded by Dallas, but they have their own building departments and their own rules. Highland Park's pool permit packet, for example, requires:

  • A survey stamped by a Registered Professional Land Surveyor
  • Oncor's approval stamp on the plan, with overhead service drops at least 10 feet horizontally from the water's edge
  • The water's edge at least 3 feet from the side or rear property or easement line (where there's no alley), and the pool behind the front building line
  • Equipment kept out of the house's required side yard and out of easements
  • Full enclosure by a fence or wall at least 48 inches high, with openings no larger than 4 inches and self-closing, self-latching gates
  • A permit fee of 1.1% of construction cost ($55 minimum)

University Park has its own process too. We check the requirements for your address before design is final.

HOAs

Much of North and Far North Dallas has HOAs or deed restrictions with architectural review. We prepare what the committee needs (site plan, renderings, materials) during design, so HOA approval comes before the city permit and well before a crane is booked.

The ground under Dallas: black clay

Most of Dallas sits on the Blackland Prairie. Its signature soil, Houston Black clay, is the official Texas state soil and is famous among engineers for how much it shrinks and swells as moisture changes. It cracks wide open in a dry August and seals up tight when it's wet. That movement is the same reason Dallas keeps so many foundation-repair crews busy.

What that means for your pool:

  • The slab matters as much as the pool. A container pool must sit on a level concrete slab, or on piers for raised and sloped installs. Its design should account for your site's soil, not be copied from a generic spec.
  • Drainage is part of the foundation. Water running toward the slab, or pooling against it, is what drives seasonal movement. We grade and drain the pad as part of the install.
  • Consistent moisture helps. Big swings, like a flooded corner next to a bone-dry one, are what move things. Gutters, downspouts and irrigation get looked at during the site survey.
  • Raised pools use piers. On sloped Dallas lots, such as along White Rock Creek or the Kessler Park bluffs, the pool can sit on concrete pillars and steel piers, each a different height, so it's dead level. See container pools on sloped yards.

Delivery and crane day in Dallas

Your pool ships finished and water-tested from our fabrication partner in Georgetown and goes into your yard by crane, usually over the house, garage or fence. In Dallas, the details that decide crane day are:

  • Alleys. Many Dallas lots are alley-loaded. An alley can be the best crane position or the worst, depending on width, poles and lines.
  • Overhead power lines. Oncor distribution lines often run along Dallas alleys and rear lot lines. Federal safety rules generally require a crane to stay 20 feet from power lines unless the utility de-energizes them, so line placement can change where the crane sets up. We flag this at the site survey.
  • Mature trees. Live oaks and pecans over the yard limit crane reach. Their roots also affect where a slab can go.
  • Street setup. If the crane has to sit in the street, we check whether the city needs a street-use permit and plan traffic around it.
  • 811 first. Before any digging for the slab, piers or trench, Texas law expects a free Texas 811 utility locate at least two business days ahead. We call it in.

Which size fits a typical Dallas lot?

  • Small infill backyard: 8x20 plunge-and-lounge, often along the back fence or side yard
  • Lap swimmers with a long, narrow yard: 8x40 or 8x60
  • Families with room to play: 16x20 or 16x40 (two containers side by side; oversize delivery)
  • Want a spa? We build the spa inside the main container with a divider, so it's one crane pick.

How a Dallas project works

  1. Get an estimate. Send photos, your address and your survey if you have one. A real person replies within one business day.
  2. Design consultation. A short call with me, Justin Hill (fabrication) and Juan Valles (installation). I'll send a 2–3 minute intro deck first.
  3. Sign. 50% at signing, 40% at pool delivery, 10% at completion. Written workmanship warranty.
  4. Site survey, then HOA, district review and city permits.
  5. Build in Georgetown while we prep your pad. The pool is water-tested before it ships.
  6. Crane day, hookups, startup, then decking and finish.

Get an estimate

Dallas FAQs

Do I need a permit for a container pool in Dallas?

Yes. Dallas only exempts prefabricated pools that sit fully above grade, hold 5,000 gallons or less and are under 24 inches deep. A container pool exceeds those limits, so it needs a pool permit plus separate electrical and plumbing permits.

Do you install in Highland Park and University Park?

Yes. They're separate towns with their own permit rules. Highland Park, for example, requires an RPLS-stamped survey, Oncor approval on the plan, a 3-foot setback from the water's edge and a 48-inch enclosure. We confirm the rules for your address before design is final.

Will Dallas clay crack my pool's slab?

Dallas's Houston Black clay shrinks and swells with moisture, so the slab or piers and the drainage around them are designed for your site. That's the most important part of a Dallas install.

Can a crane reach my backyard from the alley?

Often, yes. Alley width, utility poles, overhead lines and trees decide it. Cranes generally have to keep 20 feet from power lines unless they're de-energized. We check access before you pay for design.

More pool questions

Will the steel shell rust?

Not if the coatings are kept up — that's the honest answer. The inside is sealed with a seamless polyurea liner and the outside is coated before it leaves the shop. A coated, maintained shell holds up for decades; a scratch left open for a year doesn't. We show you what to check each season, and we can handle touch-ups.

Can a container pool be moved later?

That's one of its biggest advantages over a poured pool. Because the shell is a discrete steel structure rather than a hole in the ground, it can be disconnected, lifted, and relocated if you move or want to reposition it in the yard — something that's simply not possible with gunite.

Is a shipping container safe to swim in?

Yes. We don't clean out an old container and fill it with water. Every pool starts as a new one-trip container, cut to height and rebuilt as a pool: a 3/16" steel plate floor on a welded steel tube frame, a steel tube cap around the top edge, and a seamless spray-applied polyurea waterproof liner. It's permitted and fenced like any other residential pool.

Also installing near Dallas

Outside North Texas? We travel for installs statewide and ship pools anywhere in the U.S.

Sources

The pools

Six base models

READY TO GET STARTED?

Send your project details. A real person replies within one business day.

Designs, pricing and timelines are preliminary until a written agreement.